EPDM membranes and roofing materials

RubberGard EPDM membrane 1.14 mm

Non-reinforced EPDM roofing membrane. For roofs, canopies, garages and ponds.

You will also need: QuickSeam Splice Tape, QuickPrime Plus

RubberGard EPDM membrane 1.52 mm

The thickest EPDM membrane. Green roofs, terraces, roofs with solar panels.

You will also need: QuickSeam Splice Tape, QuickPrime Plus

QuickSeam Splice Tape — seam tape

Tape for joining EPDM sheets. 30.5 m per roll.

You will also need: QuickPrime Plus

QuickSeam FormFlash — detailing flashing

Uncured EPDM flashing for corners, pipes and T-joints. 15.25 m per roll.

You will also need: QuickPrime Plus

QuickSeam Flashing — edge and detail flashing

EPDM flashing tapes: 5" (127 mm, 30.5 m) for roof edge metal and 18" SA (450 mm, 15.25 m) for details and repairs.

You will also need: QuickPrime Plus

QuickSeam RPF Strip — perimeter fastening strip

Reinforced strip for securing the membrane at walls and parapets. 30.5 m per roll.

You will also need: QuickPrime Plus

152 mm × 30,5 m · 1 roll

QuickSeam RMA Strip

Strip for mechanical attachment without penetrating the membrane. 30.5 m per roll.

You will also need: QuickPrime Plus, V-Plates

254 mm × 30,5 m · 1 roll

QuickSeam Batten Cover Strip

Cover strip over the batten bar. 30.5 m per roll.

You will also need: QuickPrime Plus

152 mm × 30,5 m · 1 roll

QuickSeam Pipe / Conduit Flashing — pipe boot

Pre-moulded EPDM boot with stainless steel clamp: Pipe for pipes Ø 25–152 mm, Conduit for cables and small pipes Ø 13–64 mm.

You will also need: QuickPrime Plus

QuickSeam Penetration Pocket Kit

Pocket for pipe clusters and structural sections. Filled with S-10 pourable sealer.

You will also need: Pourable Sealer S-10, QuickPrime Plus

QuickSeam Drain Connector — roof drain connector

EPDM connector for a roof drain: round (Ø 330 / 140 mm) or square (320 × 350 mm, opening 138 × 105 mm).

You will also need: QuickPrime Plus

QuickSeam Walkway Pad

Rubber pad 76 × 76 cm for maintenance walkways on the roof.

You will also need: QuickPrime Plus

1 pad

Bonding Adhesive BA-2012 — EPDM adhesive

Contact adhesive for fully adhering EPDM membrane to the substrate.

Bonding Adhesive BA-2012 S/TF — canister adhesive

Adhesive in a 22 l canister for fast bonding of upstands. Works only with the Spray Gun and the 4 m hose.

You will also need: Spray Gun Professional, 4 m hose for adhesive canister

22 l canister

Bonding Adhesive BA-2004 T

Polychloroprene contact adhesive for EPDM, 18.9 l pail.

18.9 l pail

Modular Water Based Bonding Adhesive E

Water-based adhesive for bonding EPDM to timber decks.

20 l pail

I.S.O. Twin Pack — insulation adhesive

Two-component adhesive for bonding insulation boards.

1 kit

QuickPrime Plus — primer

Primer for QuickSeam tapes and accessories. Without it the tape will not hold.

You will also need: QuickScrubber kit

Lap Sealant HS — lap sealant

Sealant for FormFlash and SA Flashing edges, T-joints and bars.

1 cartridge

Water Block Seal S-20

Butyl sealant used under compression — for bars and drains.

1 cartridge

Pourable Sealer S-10

Two-component sealer for penetration pockets and green roof seams.

1 kit 3.78 l

Splice Wash SW-100 — membrane cleaner

Cleaner for dirty or weathered EPDM membrane before priming.

Cleaner C-20 — aerosol cleaner

For removing adhesive and sealant residue, 500 ml.

1 aerosol can 500 ml

QuickScrubber kit

Handles and pads for applying QuickPrime: 4 handles + 30 pads.

box: 4 handles + 30 pads

QuickScrubber Plus Stand-Up kit

Priming while standing: 4 long-pole handles + 20 pads.

box: 4 handles + 20 pads

QuickScrubber handle

Handle for QuickScrubber pads.

QuickScrubber pads

Replacement pads for the QuickScrubber handle.

Double-ended silicone seam roller

Heat-resistant silicone roller for rolling seams.

1 roller

QuickRoller — long-handled seam roller

Heavy silicone roller for rolling seams while standing.

1 roller

Spray Gun Professional — adhesive spray gun

Professional spray gun with extension for BA-2012 S/TF canister adhesive.

You will also need: 4 m hose for adhesive canister

1 gun

4 m hose for adhesive canister

4 m hose between the canister and the gun.

You will also need: Spray Gun Professional

1 hose

Termination Bar — aluminium termination bar

Aluminium bar for the top edge of the membrane on a wall, 3.05 m.

You will also need: Water Block Seal S-20

1 bar 3.05 m

Metal Batten Strip

Steel batten strip for securing the membrane: straight 3.05 m bars or a 67 m coil.

You will also need: QuickSeam Batten Cover Strip

All-Purpose Fasteners

Fasteners for steel deck, plywood and timber. Not for concrete.

Heavy Duty Fasteners

Fasteners for steel, timber and concrete.

Insulation Fastening Plates

Ø 76 mm plates for fastening insulation boards.

pack of 1000

V-Plates

Ø 57 mm plates for fastening RMA and RPF strips.

pack of 500

V-Gard vapour control membrane

Self-adhesive vapour control layer: reinforced aluminium foil with a bitumen adhesive layer.

SA-19 Primer

Primer under the V-Gard self-adhesive vapour control layer.